Troubleshooting Camo Studio for iPad

Updated

Working with audio

Currently, iPadOS 17 only permits audio through a single source. This can be the iPad’s own microphone or one connected via a USB cable or USB hub. However, if you want to capture multiple audio sources, e.g. a gamer who needs gameplay sound mixed with their commentary, a musician who uses separate microphones for voice and instrument, or an interviewer who wants to capture both sides of a conversation, you have a few options to capture multiple sound sources for your stream or recording.

The first option is to pair Camo Studio with an iOS or Android device running Camo Camera, and then select one its microphones (or a microphone connected to your phone) as the audio source for your voice, as demonstrated in the video below. You can then designate your capture card as the second audio source, and record or stream with both in Camo Studio.

The second is to use an audio interface that has at least two input ports. If you're using two microphones, you can simply plug both into the interface, and connect the interface to a powered hub that also leads into your iPad (we recommend a powered Thunderbolt hub to ensure it has enough power). You can adjust your audio levels according to the instructions for your interface, and then select it as your audio source within Camo.

If your sound setup consists of a microphone plus a video source like a laptop or gaming console, you may need a 3.5mm to XLR cable that runs from your device's headphone port to the interface. If your interface accepts other types of input in addition to XLR, you may be able to use a different cable.

Note that some devices may introduce electrical noise like buzzing or humming when connected to your interface. The most common cause of this is interference created by a ground loop, which introduces a small electrical current into the low voltage signal path. To fix it, you may need to add an inexpensive ground loop isolator to the setup.

A third option for enabling multi-source audio on the iPad is to use a wireless microphone setup. This consists of the following:

  • Wireless microphone with two transmitters and a receiver - something like the DJI mic, Rode Wireless GO or Neewer CM28. Note that at least one transmitter needs to have a 3.5mm audio jack
  • Capture card
  • Powered USB hub
  • iPad running Camo Studio for iPad
  • USB-C cables, a HDMI cable, and a 3.5mm TRS audio cable

Here’s how to set it up for streaming a gaming session on the Nintendo Switch: First, connect your iPad to a powered USB hub, and open Camo Studio for iPad. After placing the Switch into its dock, plug the dock in to power, and connect it with an HDMI cable to a capture card which is then plugged into the hub. Next, take the two wireless microphones, attaching the first to yourself - for capturing your voice - and connecting the second to the Switch’s headphone jack using a 3.5mm TRS audio cable. Finally, connect the microphone receiver to the powered hub and select it as our audio source in Camo Studio. After adjusting the gain settings to achieve a nice balance between the two audio sources, you're ready to stream or record with multi-source video and audio.

This configuration also works if you’re using a mirrorless or DSLR camera as your primary video source. In this case, you can use the 3.5mm audio cable to connect your mic receiver to the camera’s sound input, and simply select the capture card as your audio source.

We anticipate that future updates of either the iPadOS or Camo Studio for iPad will permit multiple audio sources to be connected more readily.

Connecting devices to your iPad

The best way to connect multiple devices to your iPad is through a hub or dock. To keep the iPad from being overtaxed, it’s helpful to use ones that’s powered, and - if you’re connecting more than a couple of peripheral - that uses the faster Thunderbolt standard. This will also enable you to keep your iPad charged while you use it.

A quick search on Amazon will result in an endless number of options that vary widely in price and quality. Here are models that we could recommend:

How can we help?

Our support team are here to help!

Our office hours are Monday to Friday, 9 AM to 5 PM GMT. The time is currently 7:29 PM GMT.

We aim to reply to all messages within one working day.

Our awesome support team

Join the community

Join a community centred around connecting our users! The Camo community will offer forums for discussion and support, video streams, games, giveaways and more as we grow.

Sign up here for the latest updates on our next events.

© 2008 - 2024 Reincubate Ltd. All rights reserved. Registered in England and Wales #5189175, VAT GB151788978. Reincubate® and Camo® are registered trademarks. Privacy policy & terms.